1. Detach the p-trap and also the horizontal expansion pipe.
Large channel-lock pliers or a monkey wrench job well to loosen up the nuts holding the pipes together. When both links are cost-free, eliminate the components. You may wish to clean the straight drainpipe pipeline to get rid of any type of possible obstruction. (This is not essential in brand-new building and construction.).
2. Separate the down drain.
Utilizing big channel-lock pliers, detach the down drainpipe coming from the sink as well as the connection that affixes it to the p-trap. When both connections are cost-free, remove the parts.
3. Loosen the big nut.
Loosen the big nut that holds the filter in place beneath the sink. Get rid of the filter body.
4. Tear off the breeze ring and also wipe the old plumbing technician’s putty.
Making use of a flathead screwdriver, loosen the 3 screws on the placing assembly and pry off the snap ring. Wipe the old plumbing technician’s putty that borders the side of the drain opening.
5. Mount the brand-new sink flange.
Area a 1/2″ rope of plumber’s putty around the drainpipe opening in the sink. Drop the new sink flange right into the drain opening as well as press it into area. Putting a weight, such as your garbage disposal, on top of the sink flange will help hold the sink flange in position while placing it to the sink. To prevent scratching your sink or the flange, position a towel between the sink surface and also the weight.
6. Install gasket and also flanges.
From under the sink, slide the fiber gasket, back-up flange as well as installing flange over the sink flange. Hold these pieces in position.
7. Slip on the installing as well as break rings.
Next off, slip on the placing ring and break ring. Tighten up the 3 installing screws, at the same time tightening up each screw a couple of turns each time till the installing setting up is evenly as well as firmly seated versus the bottom of the sink.
8. Remove the dishwasher knockout plug.
If using a dishwasher, you will need to touch out the dish washer knockout plug. Lay the garbage disposal on its side and make use of a screwdriver and also hammer to tap it out. Next off, get rid of the loose knockout plug from inside the garbage disposal.
9. Attach the electric.
Hardwired Unit:.
Turn the garbage disposal over and eliminate electric cover plate. Take out cords. Put cable port (not included) and also run electric wire with gain access to hole on bottom of garbage disposal. Tighten cable connector. Push cables into garbage disposal (do not displace cardboard shield) and also replace electrical cover plate.
If you have a hardwired device and also you’re aiming to affix a cord, you will certainly require a power cord set.
Corded Unit:.
For a garbage disposal with a factory-installed cord, simply plug in to the outlet under your sink after completing the remainder of the actions.
10. Hang the garbage disposal.
Hang the garbage disposal by straightening the 3 placing tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in place, turn the reduced placing ring till all three tabs are locked right into the mounting setting up.
11. Put the discharge tube.
Insert the discharge tube right into the discharge coupler, after that slide the clamp over the discharge tube and setting it in the groove on the rubber tailpipe coupler.
12. Line up the discharge tube with the drainpipe pipe.
Revolve the garbage disposal to make sure that the discharge tube is straightened with the drainpipe catch. If the discharge tube is too long, cut off as much of television as needed. If it is too brief, you can purchase an extension. If you are linking the garbage disposal to a dishwashing machine, it may be attached through an air space. Use a pipe clamp to connect the drainpipe tube to the dish washer inlet.
13. Lock the garbage disposal in position.
Now that whatever is installed and ready, lock the garbage disposal to the sink installing setting up using the wrench that included the system. Insert the Quiet Collar Sink Baffle right into the sink opening by pushing it into the sink up until it snaps into place.
14. Evaluate the garbage disposal.
Test for leaks at the sink flange, dish washer, tail-pipe as well as installing assembly connections. Finally, turn on the electric breaker to examine its procedure. Appreciate your new garbage disposal!
Plumbing Service – Repair and replacement – Garbage Disposal Installation in Yorba Linda
How to Install a Garbage Disposal in Yorba Linda