1. Shut off power to the garbage disposal and also separate the down trap.
Turn off the electrical power at the circuit box or circuit breaker. Then, making use of adjustable pliers, separate the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the mounting assembly.
Assistance the garbage disposal with one hand and place completion of the wrenchette or screwdriver right into the ideal side of one mounting lug on the reduced installing ring. Raise the garbage disposal somewhat and also loosen the reduced mounting ring by pressing or pulling the wrenchette or screwdriver to the left until the garbage disposal is devoid of the installing assembly.
3. Disconnect the electric.
Lay the garbage disposal on its side and get rid of the electric cover plate from the bottom. Loosen up the green ground screw and also eliminate cable adapters. Separate garbage disposal cords from electrical supply cables. Loosen up screws on the electrical clamp connector as well as get rid of cords from the garbage disposal.
4. Eliminate existing installing hardware if equipment replacement needed. Otherwise miss to tip 12.
To eliminate the existing placing hardware, loosen the three mounting screws, tear the breeze ring off with a screwdriver and eliminate the old placing assembly.
5. Get rid of the old sink flange as well as putty.
Push the old sink flange up through the sink hole. Make use of a screwdriver or putty knife to very carefully scratch all old putty from the side of the sink opening
. Install the brand-new sink flange, gasket and also rings.
Location a 1/2 inch rope of plumber’s putty around the drainpipe opening in the sink. Go down the brand-new sink flange into the drain opening as well as press it right into location. Positioning a weight, such as the garbage disposal, in addition to the sink flange will certainly assist hold the sink flange in place while installing the sink flange to the sink. To avoid scratching your sink or the flange, put a towel between the sink surface and the weight. From under the sink, slide the fiber gasket, back-up flange and placing flange over the sink flange. Hold these items in place.
7. Eliminate the dish washer ko plug.
If utilizing a dish washer, you will need to tap out the dish washer knockout plug. Lay the garbage disposal on its side and make use of a screwdriver and hammer to touch it out. Next, eliminate the loose ko plug from inside the garbage disposal.
8. Connect the electrical.
Hardwired Unit:
Transform the garbage disposal over and also eliminate electric cover plate. Pull out cables. Place cable television connector (not included) and run electrical cord through gain access to opening on base of garbage disposal. Tighten cable port. Push cords into garbage disposal (do not displace cardboard shield) and also change electric cover plate.
If you have a hardwired system and also you’re looking to attach a cable, you will need a power cable kit.
Corded System:
For a garbage disposal with a factory-installed cord, just plug in to the outlet under your sink after completing the remainder of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the 3 placing tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in place, transform the reduced mounting ring until all 3 tabs are locked into the mounting assembly. The garbage disposal will certainly now hang on its own.
10. Put the discharge tube.
Place the discharge tube right into the discharge coupler, then move the clamp over the discharge tube and position it in the groove on the rubber tailpipe coupler.
11. Straighten the discharge tube with the drain catch.
Turn the garbage disposal so that the discharge tube is straightened with the drain trap. If the discharge tube is as well long, cut off as much as needed. If it is also short, you can purchase an extension.
12. Lock the garbage disposal in position.
If you are attaching the garbage disposal to a dishwasher, it may be connected through an air gap. Use a tube clamp to attach the drain pipe to the dishwashing machine inlet. Now that every little thing is mounted as well as ready, secure the garbage disposal to the sink installing setting up making use of the wrenchette that included the system. For Development designs, insert the Quiet Collar ® Sink Baffle right into the sink opening by pushing it into the sink up until it snaps right into area.
13. Test the garbage disposal.
For all designs, you need to examine for leakages at the sink flange, dishwasher, tail-pipe and also mounting assembly links. Lastly, turn on the electrical breaker to test its operation.
Garbage Disposal Installation: In Detail in Glendale
Everything You Required to Find Out About Garbage Disposals in Glendale