1. Shut off power to the garbage disposal and also separate the down catch.
Turn off the electrical power at the circuit box or circuit breaker. Then, utilizing flexible pliers, detach the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the mounting setting up.
Assistance the garbage disposal with one hand as well as place completion of the wrenchette or screwdriver into the best side of one placing lug on the lower mounting ring. Lift the garbage disposal slightly and loosen up the lower installing ring by pushing or drawing the wrenchette or screwdriver to the left up until the garbage disposal is devoid of the mounting assembly.
3. Detach the electric.
Lay the garbage disposal on its side as well as remove the electric cover plate from all-time low. Loosen up the green ground screw and remove wire connectors. Disconnect garbage disposal cords from electric supply cords. Loosen up screws on the electric clamp connector and get rid of cables from the garbage disposal.
4. Get rid of existing mounting equipment if hardware replacement required. Or else miss to tip 12.
To remove the existing placing equipment, loosen up the three placing screws, pry the snap ring off with a screwdriver and remove the old mounting assembly.
5. Eliminate the old sink flange and putty.
Push the old sink flange up via the sink hole. Utilize a screwdriver or putty knife to thoroughly scratch all old putty from the edge of the sink hole
. Install the brand-new sink flange, gasket and rings.
Location a 1/2 inch rope of plumbing professional’s putty around the drain opening in the sink. Go down the new sink flange into the drain opening and press it right into location. Placing a weight, such as the garbage disposal, on top of the sink flange will certainly help hold the sink flange in place while placing the sink flange to the sink. To prevent scratching your sink or the flange, position a towel in between the sink surface as well as the weight. From under the sink, slide the fiber gasket, backup flange and also placing flange over the sink flange. Hold these items in place.
7. Remove the dishwasher ko plug.
If using a dishwashing machine, you will certainly require to tap out the dishwasher knockout plug. Lay the garbage disposal on its side and make use of a screwdriver and hammer to touch it out. Next off, eliminate the loose knockout plug from inside the garbage disposal.
8. Attach the electrical.
Hardwired System:
Turn the garbage disposal over as well as get rid of electric cover plate. Pull out cables. Insert cord connector (not consisted of) as well as run electric wire through accessibility hole on base of garbage disposal. Tighten wire port. Press cords into garbage disposal (do not displace cardboard guard) and change electric cover plate.
If you have a hardwired device and also you’re aiming to affix a cable, you will need a power cable package.
Corded Device:
For a garbage disposal with a factory-installed cord, simply connect in to the electrical outlet under your sink after completing the rest of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the 3 placing tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in position, turn the lower mounting ring till all three tabs are secured right into the installing setting up. The garbage disposal will now hang on its own.
10. Insert the discharge tube.
Put the discharge tube into the discharge coupler, then slide the clamp over the discharge tube and also setting it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drain catch.
Rotate the garbage disposal to make sure that the discharge tube is lined up with the drainpipe catch. If the discharge tube is also long, cut off as high as needed. If it is as well short, you can acquire an expansion.
12. Lock the garbage disposal in position.
If you are linking the garbage disposal to a dishwashing machine, it might be linked through an air void. Utilize a tube clamp to connect the drain tube to the dishwashing machine inlet. Since every little thing is installed as well as ready, secure the garbage disposal to the sink placing assembly making use of the wrenchette that featured the system. For Advancement designs, insert the Quiet Collar ® Sink Baffle into the sink opening by pushing it right into the sink up until it snaps into area.
13. Test the garbage disposal.
For all models, you should evaluate for leakages at the sink flange, dishwasher, tail-pipe as well as mounting setting up connections. Finally, turn on the electrical breaker to evaluate its procedure.
New Garbage Disposal Installation Guide in Northridge
DIY Garbage Disposal Installation in Northridge