1. Turn off power to the garbage disposal as well as disconnect the down trap.
Turn off the electric power at the circuit box or breaker. After that, using adjustable pliers, detach the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing setting up.
Support the garbage disposal with one hand and insert the end of the wrenchette or screwdriver right into the best side of one installing lug on the reduced mounting ring. Raise the garbage disposal slightly and also loosen the reduced installing ring by pressing or pulling the wrenchette or screwdriver to the left until the garbage disposal is devoid of the mounting setting up.
3. Detach the electrical.
Lay the garbage disposal on its side and also remove the electric cover plate from the bottom. Loosen up the green ground screw as well as get rid of cable adapters. Detach garbage disposal wires from electric supply cables. Loosen up screws on the electrical clamp adapter and also get rid of cords from the garbage disposal.
4. Remove existing placing equipment if equipment replacement needed. Or else miss to step 12.
To remove the existing placing hardware, loosen up the three mounting screws, pry the breeze ring off with a screwdriver as well as remove the old mounting setting up.
5. Remove the old sink flange as well as putty.
Press the old sink flange up with the sink opening. Utilize a screwdriver or putty knife to very carefully scratch all old putty from the edge of the sink hole
. Set up the new sink flange, gasket as well as rings.
Location a 1/2 inch rope of plumbing’s putty around the drainpipe opening in the sink. Drop the new sink flange right into the drain opening and press it into location. Putting a weight, such as the garbage disposal, on top of the sink flange will assist hold the sink flange in place while mounting the sink flange to the sink. To stay clear of damaging your sink or the flange, put a towel in between the sink surface and the weight. From under the sink, slide the fiber gasket, backup flange and installing flange over the sink flange. Hold these items in place.
7. Eliminate the dishwashing machine ko plug.
If making use of a dish washer, you will need to tap out the dish washer ko plug. Lay the garbage disposal on its side as well as use a screwdriver as well as hammer to tap it out. Next, eliminate the loosened knockout plug from inside the garbage disposal.
8. Link the electric.
Hardwired Unit:
Turn the garbage disposal over and eliminate electrical cover plate. Take out cables. Place cable port (not consisted of) and run electrical wire through gain access to hole on base of garbage disposal. Tighten up cord port. Push wires into garbage disposal (do not displace cardboard guard) and change electrical cover plate.
If you have a hardwired system as well as you’re seeking to affix a cable, you will need a power cable set.
Corded Device:
For a garbage disposal with a factory-installed cord, merely connect in to the outlet under your sink after finishing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the 3 mounting tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in place, transform the reduced placing ring until all three tabs are secured right into the installing assembly. The garbage disposal will certainly currently hang on its own.
10. Place the discharge tube.
Insert the discharge tube right into the discharge coupler, then move the clamp over the discharge tube and setting it in the groove on the rubber tailpipe coupler.
11. Straighten the discharge tube with the drain trap.
Turn the garbage disposal to make sure that the discharge tube is aligned with the drainpipe catch. If the discharge tube is too long, removed as much as required. If it is too brief, you can buy an expansion.
12. Lock the garbage disposal in place.
If you are linking the garbage disposal to a dishwasher, it may be attached via an air space. Make use of a tube clamp to affix the drain pipe to the dish washer inlet. Since everything is set up and ready, secure the garbage disposal to the sink placing setting up utilizing the wrenchette that included the unit. For Evolution models, insert the Quiet Collar ® Sink Baffle into the sink opening by pressing it into the sink up until it snaps into area.
13. Test the garbage disposal.
For all versions, you need to test for leaks at the sink flange, dishwasher, tail-pipe as well as mounting setting up links. Lastly, turn on the electrical breaker to evaluate its procedure.
Plumbing Service – Repair and replacement – Garbage Disposal Installation in Covina
Ways to Install a Garbage Disposal in Covina