1. Switch off power to the garbage disposal as well as separate the down catch.
Shut off the electric power at the fuse box or circuit breaker. Then, making use of adjustable pliers, detach the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the installing assembly.
Assistance the garbage disposal with one hand and also put completion of the wrenchette or screwdriver right into the best side of one placing lug on the reduced mounting ring. Lift the garbage disposal a little and also loosen up the lower installing ring by pushing or drawing the wrenchette or screwdriver to the left until the garbage disposal is free from the mounting setting up.
3. Disconnect the electrical.
Lay the garbage disposal on its side and also remove the electrical cover plate from the bottom. Loosen up the green ground screw and also get rid of wire adapters. Detach garbage disposal cables from electric supply cables. Loosen up screws on the electrical clamp connector and remove cables from the garbage disposal.
4. Remove existing mounting equipment if hardware replacement required. Otherwise miss to step 12.
To get rid of the existing placing equipment, loosen the 3 installing screws, pry the breeze ring off with a screwdriver and also eliminate the old installing assembly.
5. Eliminate the old sink flange and putty.
Press the old sink flange up with the sink opening. Utilize a screwdriver or putty knife to very carefully scrape all old putty from the side of the sink hole
. Mount the new sink flange, gasket as well as rings.
Location a 1/2 inch rope of plumber’s putty around the drainpipe opening in the sink. Go down the brand-new sink flange right into the drain opening as well as press it into location. Placing a weight, such as the garbage disposal, in addition to the sink flange will certainly assist hold the sink flange in position while placing the sink flange to the sink. To prevent damaging your sink or the flange, put a towel between the sink surface area and the weight. From under the sink, slide the fiber gasket, back-up flange and placing flange over the sink flange. Hold these items in position.
7. Get rid of the dish washer knockout plug.
If using a dishwasher, you will certainly require to touch out the dish washer ko plug. Lay the garbage disposal on its side as well as use a screwdriver as well as hammer to touch it out. Next, get rid of the loosened ko plug from inside the garbage disposal.
8. Attach the electrical.
Hardwired System:
Turn the garbage disposal over and also get rid of electric cover plate. Take out cables. Put cord adapter (not included) and run electrical cable television via gain access to opening on base of garbage disposal. Tighten up cable television connector. Press cables right into garbage disposal (do not displace cardboard guard) as well as replace electrical cover plate.
If you have a hardwired unit and also you’re seeking to attach a cord, you will need a power cable set.
Corded Unit:
For a garbage disposal with a factory-installed cord, merely connect in to the outlet under your sink after completing the remainder of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the three placing tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in place, turn the reduced installing ring up until all three tabs are locked into the installing setting up. The garbage disposal will certainly currently hang by itself.
10. Put the discharge tube.
Put the discharge tube right into the discharge coupler, then move the clamp over the discharge tube and position it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drainpipe catch.
Turn the garbage disposal to ensure that the discharge tube is aligned with the drainpipe trap. If the discharge tube is also long, removed as much as necessary. If it is too brief, you can acquire an expansion.
12. Lock the garbage disposal in place.
If you are attaching the garbage disposal to a dishwashing machine, it might be connected through an air space. Use a hose pipe clamp to connect the drainpipe pipe to the dishwashing machine inlet. Now that whatever is installed as well as ready, lock the garbage disposal to the sink placing assembly utilizing the wrenchette that came with the system. For Development versions, place the Quiet Collar ® Sink Baffle into the sink opening by pressing it right into the sink until it snaps into place.
13. Check the garbage disposal.
For all designs, you need to examine for leakages at the sink flange, dishwasher, tail-pipe as well as placing setting up links. Finally, switch on the electrical breaker to evaluate its operation.
How to Choose a Garbage Disposal in Compton
How to Install a Garbage Disposal in Compton