1. Switch off power to the garbage disposal as well as disconnect the down trap.
Turn off the electrical power at the fuse box or circuit breaker. Then, using flexible pliers, separate the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the mounting assembly.
Support the garbage disposal with one hand and also put the end of the wrenchette or screwdriver into the right side of one placing lug on the lower mounting ring. Lift the garbage disposal somewhat as well as loosen the reduced installing ring by pressing or drawing the wrenchette or screwdriver to the left until the garbage disposal is without the placing assembly.
3. Disconnect the electrical.
Lay the garbage disposal on its side and also remove the electric cover plate from the bottom. Loosen up the green ground screw and get rid of wire ports. Disconnect garbage disposal wires from electric supply wires. Loosen up screws on the electric clamp port and also get rid of cords from the garbage disposal.
4. Eliminate existing placing hardware if equipment replacement needed. Or else skip to tip 12.
To get rid of the existing mounting hardware, loosen up the 3 mounting screws, pry the snap ring off with a screwdriver as well as get rid of the old placing setting up.
5. Eliminate the old sink flange and also putty.
Press the old sink flange up with the sink hole. Use a screwdriver or putty blade to meticulously scuff all old putty from the edge of the sink opening
. Mount the new sink flange, gasket and also rings.
Place a 1/2 inch rope of plumbing technician’s putty around the drain opening in the sink. Drop the new sink flange into the drainpipe opening and press it right into location. Putting a weight, such as the garbage disposal, on top of the sink flange will assist hold the sink flange in place while installing the sink flange to the sink. To stay clear of scratching your sink or the flange, place a towel in between the sink surface and also the weight. From under the sink, slide the fiber gasket, back-up flange as well as mounting flange over the sink flange. Hold these items in position.
7. Get rid of the dishwasher knockout plug.
If using a dishwashing machine, you will certainly require to tap out the dishwashing machine ko plug. Lay the garbage disposal on its side and use a screwdriver and hammer to tap it out. Next off, get rid of the loosened ko plug from inside the garbage disposal.
8. Connect the electric.
Hardwired System:
Turn the garbage disposal over as well as eliminate electrical cover plate. Take out wires. Place cable connector (not consisted of) as well as run electric wire through access hole on base of garbage disposal. Tighten up cable television adapter. Push cables into garbage disposal (do not displace cardboard shield) and also replace electric cover plate.
If you have a hardwired unit as well as you’re wanting to affix a cable, you will certainly need a power cable set.
Corded System:
For a garbage disposal with a factory-installed cable, just plug in to the outlet under your sink after completing the rest of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the three installing tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in place, transform the reduced mounting ring up until all three tabs are secured right into the installing assembly. The garbage disposal will now hang by itself.
10. Insert the discharge tube.
Place the discharge tube right into the discharge coupler, after that move the clamp over the discharge tube and placement it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drainpipe trap.
Turn the garbage disposal so that the discharge tube is lined up with the drainpipe trap. If the discharge tube is also long, cut off as long as needed. If it is as well brief, you can purchase an expansion.
12. Lock the garbage disposal in position.
If you are connecting the garbage disposal to a dish washer, it might be connected through an air gap. Utilize a hose pipe clamp to attach the drainpipe hose to the dishwasher inlet. Now that whatever is mounted as well as in position, lock the garbage disposal to the sink placing setting up using the wrenchette that came with the unit. For Advancement versions, put the Quiet Collar ® Sink Baffle into the sink opening by pressing it right into the sink up until it snaps into place.
13. Check the garbage disposal.
For all versions, you should test for leakages at the sink flange, dishwasher, tail-pipe and also mounting assembly links. Lastly, turn on the electric breaker to evaluate its operation.
New Garbage Disposal Installation Guide in Sunset Beach
How to Install a Garbage Disposal in Sunset Beach