1. Switch off power to the garbage disposal as well as separate the down catch.
Shut off the electric power at the fuse box or circuit breaker. Then, making use of adjustable pliers, disconnect the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing setting up.
Assistance the garbage disposal with one hand as well as place the end of the wrenchette or screwdriver into the ideal side of one mounting lug on the lower placing ring. Raise the garbage disposal somewhat and also loosen the lower installing ring by pressing or pulling the wrenchette or screwdriver to the left until the garbage disposal is without the placing setting up.
3. Detach the electrical.
Lay the garbage disposal on its side and also get rid of the electric cover plate from all-time low. Loosen up the green ground screw and also eliminate cable adapters. Detach garbage disposal wires from electrical supply cables. Loosen screws on the electrical clamp connector and also eliminate cords from the garbage disposal.
4. Get rid of existing mounting hardware if equipment replacement needed. Otherwise skip to tip 12.
To get rid of the existing placing equipment, loosen up the three placing screws, tear the snap ring off with a screwdriver and also get rid of the old mounting setting up.
5. Eliminate the old sink flange and also putty.
Press the old sink flange up with the sink hole. Use a screwdriver or putty knife to carefully scuff all old putty from the edge of the sink hole
. Mount the brand-new sink flange, gasket and also rings.
Place a 1/2 inch rope of plumbing’s putty around the drainpipe opening in the sink. Go down the brand-new sink flange right into the drain opening as well as press it right into place. Positioning a weight, such as the garbage disposal, on top of the sink flange will aid hold the sink flange in place while mounting the sink flange to the sink. To stay clear of damaging your sink or the flange, position a towel in between the sink surface and also the weight. From under the sink, slide the fiber gasket, backup flange as well as mounting flange over the sink flange. Hold these items in place.
7. Remove the dishwasher knockout plug.
If utilizing a dishwasher, you will certainly require to tap out the dishwashing machine knockout plug. Lay the garbage disposal on its side and make use of a screwdriver as well as hammer to tap it out. Next, eliminate the loosened knockout plug from inside the garbage disposal.
8. Attach the electrical.
Hardwired Unit:
Transform the garbage disposal over and also eliminate electric cover plate. Take out wires. Insert cable port (not included) and also run electric cable through accessibility opening on base of garbage disposal. Tighten cord connector. Press cords into garbage disposal (do not displace cardboard guard) as well as replace electrical cover plate.
If you have a hardwired unit as well as you’re wanting to attach a cord, you will certainly need a power cable package.
Corded Unit:
For a garbage disposal with a factory-installed cable, simply plug in to the electrical outlet under your sink after finishing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the three mounting tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in position, transform the reduced installing ring up until all 3 tabs are secured right into the mounting setting up. The garbage disposal will currently hang on its own.
10. Place the discharge tube.
Place the discharge tube right into the discharge coupler, after that glide the clamp over the discharge tube as well as setting it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drain trap.
Rotate the garbage disposal so that the discharge tube is lined up with the drainpipe trap. If the discharge tube is too long, removed as much as needed. If it is too short, you can acquire an expansion.
12. Lock the garbage disposal in place.
If you are connecting the garbage disposal to a dishwashing machine, it may be connected with an air void. Utilize a tube clamp to attach the drain hose to the dishwashing machine inlet. Now that every little thing is set up and also ready, secure the garbage disposal to the sink installing assembly making use of the wrenchette that came with the unit. For Evolution designs, place the Quiet Collar ® Sink Baffle right into the sink opening by pressing it into the sink till it snaps right into area.
13. Check the garbage disposal.
For all designs, you should examine for leakages at the sink flange, dish washer, tail-pipe as well as installing assembly links. Finally, switch on the electrical breaker to check its operation.
How to Install a Garbage Disposal in West Covina