1. Turn off power to the garbage disposal and detach the down trap.
Shut off the electric power at the fuse box or circuit breaker. After that, using flexible pliers, disconnect the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the installing setting up.
Assistance the garbage disposal with one hand as well as place the end of the wrenchette or screwdriver right into the best side of one mounting lug on the reduced installing ring. Raise the garbage disposal somewhat and also loosen the lower mounting ring by pushing or pulling the wrenchette or screwdriver to the left till the garbage disposal is free from the installing setting up.
3. Separate the electric.
Lay the garbage disposal on its side and also remove the electrical cover plate from the bottom. Loosen the green ground screw and also get rid of cord adapters. Disconnect garbage disposal wires from electrical supply wires. Loosen up screws on the electric clamp port and also get rid of cords from the garbage disposal.
4. Remove existing installing hardware if equipment replacement needed. Otherwise avoid to step 12.
To get rid of the existing mounting hardware, loosen up the three placing screws, tear the breeze ring off with a screwdriver as well as remove the old installing assembly.
5. Remove the old sink flange and also putty.
Press the old sink flange up via the sink hole. Utilize a screwdriver or putty blade to meticulously scrape all old putty from the side of the sink opening
. Install the new sink flange, gasket as well as rings.
Area a 1/2 inch rope of plumbing professional’s putty around the drainpipe opening in the sink. Go down the new sink flange into the drain opening as well as press it right into place. Positioning a weight, such as the garbage disposal, in addition to the sink flange will help hold the sink flange in place while mounting the sink flange to the sink. To avoid scraping your sink or the flange, position a towel between the sink surface as well as the weight. From under the sink, slide the fiber gasket, backup flange and also installing flange over the sink flange. Hold these items in position.
7. Remove the dish washer ko plug.
If using a dishwashing machine, you will need to touch out the dishwashing machine ko plug. Lay the garbage disposal on its side and use a screwdriver as well as hammer to tap it out. Next off, remove the loose knockout plug from inside the garbage disposal.
8. Connect the electrical.
Hardwired Device:
Turn the garbage disposal over and remove electric cover plate. Take out wires. Place cord port (not consisted of) as well as run electrical cord with gain access to opening on base of garbage disposal. Tighten cord connector. Press wires right into garbage disposal (do not displace cardboard guard) and change electrical cover plate.
If you have a hardwired unit as well as you’re seeking to affix a cable, you will certainly require a power cable package.
Corded Device:
For a garbage disposal with a factory-installed cable, simply connect in to the electrical outlet under your sink after finishing the remainder of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the 3 mounting tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in place, turn the reduced placing ring up until all 3 tabs are secured into the placing setting up. The garbage disposal will currently hang on its own.
10. Place the discharge tube.
Put the discharge tube right into the discharge coupler, after that glide the clamp over the discharge tube and position it in the groove on the rubber tailpipe coupler.
11. Straighten the discharge tube with the drainpipe trap.
Turn the garbage disposal to make sure that the discharge tube is straightened with the drain catch. If the discharge tube is also long, cut off as much as essential. If it is as well short, you can buy an expansion.
12. Lock the garbage disposal in place.
If you are connecting the garbage disposal to a dishwashing machine, it might be attached with an air void. Utilize a hose pipe clamp to affix the drainpipe hose to the dishwasher inlet. Now that everything is installed and also ready, lock the garbage disposal to the sink installing assembly using the wrenchette that came with the unit. For Development designs, put the Quiet Collar ® Sink Baffle into the sink opening by pressing it into the sink till it snaps right into location.
13. Evaluate the garbage disposal.
For all models, you must evaluate for leakages at the sink flange, dishwasher, tail-pipe and also placing setting up connections. Finally, switch on the electrical breaker to examine its procedure.
Plumbing Service – Repair and replacement – Garbage Disposal Installation in Mission Hills
Garbage Disposal Installation: Detailed in Mission Hills